How to stabilize a christmas tree


Christmas Miracle: 8 Simple Fixes for All Your Tree Troubles

Shedding Needles

1/8

Dropping needles are a sign your Christmas tree is dry. You can combat this by buying the freshest tree possible in the first place. Then, be sure to cut a slice off the bottom of the trunk immediately before you put it into the tree stand. This removes the sap that has collected over the original cut, which allows the tree to take up water. Make sure it has LOTS of water for the first couple days, and don’t ever allow it the water to drop below the cut. You can also spray your tree with Christmas tree spray before decorating it. That will seal the surface of the needles and keep them from losing moisture.

Related: 7 Reasons Not to Chuck Your Tree After X-Mas

fotosearch.com

Bare Spots

2/8

Sometimes you don’t see that the Christmas tree you’ve selected has a big bare spot until you get it home and into the stand. If your tree stands next to a wall or corner, that’s an easy fix—just turn it around. But if that’s not the case, cut a few branches from the bottom of the tree before putting it into the stand. Then, zip tie those branches onto the interior of the branches just surrounding the gap. Trim and shape them with some pruners to help those “new branches” blend in. Once you’ve got the lights and ornaments on, no one will ever notice.

Related: Bob Vila's Top 10 Artificial Christmas Trees

fotosearch.com

Sap Removal

3/8

It’s inevitable that somewhere in between the Christmas tree farm and your home, sap will get somewhere. Usually that means its either in your car, on you, or on the carpet. For upholstery and carpet, mix a little dish soap into warm water and gently work it into the spot. Continue until the sap loosens up, and then rinse it away. Finally blot the area with dry towels. If you get sap on your hands, rub some hand sanitizer on it to break it up. Then, wash your hands with soap and water.

Related: How To—Choose the Best Christmas Tree (and Keep It Fresh)

fotosearch.com

Advertisement

The Crooked Tree

4/8

It’s really hard to get a Christmas tree to stand up straight in the stand on the first try. You need a partner. One person should drop the trunk into the stand as upright as possible and hold it, while the second person screws the eye bolts in underneath. Tighten each bolt a little bit a time. Once the tree is stable enough, the first person should then stand away from the tree and direct the bolt tightening. If the tree is leaning in one direction, the bolt on the opposite side should be tightened to straighten it up. It requires a little bit of trial and error, but with that method, you’ll eventually have success.

flickr.com via lockergnome

Leaky Stand

5/8

Place a sheet of plastic with a towel on top of it under the Christmas tree stand prior to setting it up. If you have a watering snafu, or the tree stand start to leak, this will help to protect your floor. Check the towel every day when you water the tree, so you can head off any problems sooner as opposed to later.

holidayprojectors.com

Broken Lights

6/8

So, what happens if a strand of lights goes out after you’ve decorated the tree? It’s usually one bad bulb that causes a whole string to go defunct. Check each bulb on the strand to make sure it is properly seated. Tightening a loose one may do the trick. If it doesn’t, use an extra bulb that came with the set, and swap it into each bulb socket until you find the bum light. Once you do, all the lights should come back on.

Related: Bob Vila’s 8 Tips for Hanging Holiday Lights

fotosearch.com

Advertisement

Animal Attacks

7/8

Cats and Christmas trees are natural foes. To keep your kitty from climbing the tree, wrap the base of it in a thick layer of aluminum foil. They don’t like to put their claws through it. You can also spray the tree with Citronella or Apple Bitter. Cats don’t like the smell, and more likely than not, will avoid your festive arrangements.

fotosearch.com

Baby Proofing

8/8

Toddlers are as curious about Christmas trees as cats are. But you need different methods to deter them. Place some extra baby gates around the tree to keep little ones from breaking precious ornaments or pulling the tree down on top of themselves. If a baby gates kills your Christmas spirit, decorate it with garland and bows to help it blend into the scene. Or, wrap some large empty boxes with Christmas wrap and surround the tree with a “present fence.”

fotosearch.com

Don't Miss!

If you have the money to hire a handyman for every household woe, go ahead. But if you want to hang on to your cash and exercise some self-sufficiency, check out these clever products that solve a million and one little problems around the house. Go now!

safety - How do I keep my Christmas tree from falling over?

Get a heavy stand

Growing up, my dad had a traditional stand that looks something like this:

That works for smaller trees as long as you can be sure that nobody (such as a child or pet) will disturb it. That's not at all a given. Remember that trees have extensive root systems that keep them grounded during windy periods and so it's important to get a stand that can simulate the parts of the tree that have been cut off. For that reason, I'm a proponent of a heavier stand such as this one made of cast iron:

There's something to be said for the simplicity of a really heavy, wide stand that will hold your tree firmly in place. I've been told plastic stands are sturdier than they look when they are weighted with water. They have the additional advantage of holding a gallon of water or more, which means you won't risk a dried out tree. In some ways it doesn't matter what the stand looks like since you can always cover it with a tree skirt. (And my wife insists on it even though I like the way our stand looks.)

Placing the tree in the stand

One thing I've tried is to set the tree up before removing the twine that holds the branches in place. This is a mistake for two reasons:

  1. The balance of the tree changes when the branches are fully deployed. A tree that stands straight when wrapped can sometimes end up leaning when unwrapped.

  2. My wife always wants me to rotate the tree so that the best side is facing into the room. Once the tree is secure, you don't want to mess with the balance by trying to move or rotate it.

For the sake of getting a good balance, I also think it's a mistake to attach the stand before putting the tree upright. Or rather, you're going to need to readjust it anyway and it probably won't buy you anything—especially if you have a heavy stand.

Attaching the tree to the stand

Here's where my stand fails me. It attaches to the tree with three screws. Three is the absolute minimum number of points need to hold a trunk in place and it doesn't seem to be enough. If I try to adjust one side, the tree starts falling over and I need help holding it up. (My father's stand had the same problem, but image searches show most of the traditional design have 4 screws plus a ring to hold the truck more securely.)

This year I hit on a solution that's so simple I can't figure out how it didn't occur to me before: I put 2x4 scraps between the screws and the trunk. This has the advantage of spreading the side pressure to a larger area and also makes adjustments easier since the bolts don't screw into the trunk itself. For added security, I packing in extra scraps of wood to brace the tree now that I have it secured to the stand.

Looking around, I see that newer designs use two levels of screws or even "hug" the trunk with a pedal operated cable. I don't have any experience with these designs, but if the stand is heavy enough (see above) they are probably improvements over the three-screw stand that I'm using.

Consider a guyline

Here in California, we are encouraged to secure everything in case of earthquake. Given the excitement of the season, I like to secure our tree in case of childquake. It's a bit of a hassle, but in years past, I've been glad to have a bit of safety from tree fall when its balance shifted due to watering and decorations. It need not be an eyesore either—the line might be secured to a hook in the wall behind the tree.

I've used monofilament fishing line to attach our tree to a hook in the ceiling. Since the fishing line is designed to be invisible (or close to it) in water, most people won't see it. A bonus advantage is that you know what your line is rated and can estimate how many strands will suffice. If you do fish in the summer, its a good idea to replace your line between fishing seasons to avoid tangles, so this is a perfect opportunity.

Decorate the Christmas tree safely! - Safety on holidays and during mass celebrations

During the New Year and Christmas holidays it is so nice to enjoy warm and cheerful evenings with family and friends. However, it is worth remembering that a Christmas tree burning with multi-colored lights is not only the main decoration of the New Year's house, but a source of danger. Therefore, special attention should be paid to its fire safety. After all, the New Year is candles, crackers and lights, and Christmas trees , unfortunately, burn very well. Moreover, artificial ones also emit toxic substances, quickly melt and “spread”, which means that it will be more difficult to eliminate the source of ignition.

When choosing an artificial Christmas tree , it is safer to give preference to models that have a fireproof impregnation (this information is indicated on the packaging).

It is better to install a live Christmas tree two or three days before the New Year. If you bought it earlier, then hold it until it is installed on the balcony: it will be easier for it to adapt to temperature changes. After that, she needs to update the cut by sawing off a few centimeters from the trunk.

Spruce stand must be solid and solid. If you decide to stay on a live spruce, then make sure that it is not dry. The tree needs to be fed with water by placing it in a special form with a water tank or in a bucket of wet sand. This will prevent the needles from drying out and sprinkling quickly, and most importantly, it will increase fire safety. Spraying a Christmas tree decorated with electric garlands should be done with great care. If the garland is intended for both home and outdoor use, then there are no particular problems. Otherwise, spraying should be resorted to only in extreme cases, and before switching on tree must be left to dry completely.

Install the Christmas tree away from electrical and heating appliances and sources of open fire (fireplaces, gas stoves). It must be remembered that spruce needles flare up instantly and if it flares up strongly, it is quite difficult to extinguish it. Candles and sparklers should not be placed on the Christmas tree, especially in combination with cotton "snow" and paper toys. Let the candles stand on the tables, but even there they should not burn unattended. If you leave the table, be sure to pay them off.

The Christmas tree should not be too big for the room it will be in. Let its top be at least fifty centimeters short of the ceiling. This is especially important if the ceilings are lined with flammable material. The Christmas tree should not be placed close to the walls covered with wallpaper and next to the curtains. In addition, it is not recommended to install Christmas trees in such a way that they interfere with progress - in case of an emergency, they will create a significant obstacle.

If there are small children in the house, then if possible, it is better to install the spruce at such a height that they cannot reach the lower branches, while avoiding household injuries.

Be sure to follow fire safety regulations and be responsible in the choice and use of electrical decorations during the New Year and Christmas holidays.

Faulty and non-certified electrical appliances must not be used to decorate Christmas tree . Children should not have access to controllers (control units for the operation of an electric garland and / or Christmas tree ), wires and sockets.

To prevent the tree from tipping over and injuring the child, it must be correctly assembled and securely installed, and toys evenly distributed on it. You need to assemble an artificial Christmas tree in accordance with the instructions. In the room where the Christmas tree stands, kids should only be under the supervision of adults. For children's safety, it is better to decorate the Christmas tree with light, unbreakable decorations - bows, cones, fiberglass balls, etc.

Be conscious about the choice of garlands. It is better to choose products coated with a flame retardant and tested in a modern laboratory. Such information must be indicated on the packaging.

Garlands must be equipped with fuses, without them, during power surges, overheating and ignition of the wiring may occur. Never turn on the garland in the presence of bare wires, as well as homemade connections. In addition, the elements of the garland should not come into contact with the "rain", because the metallized foil can short-circuit the wiring.

The garland must be checked before placing it on the Christmas tree. At home, it is recommended to use decorations in which the number of lights does not exceed 50. And do not forget that more than three garlands cannot be included in one outlet. If you have any doubts, there is not at least one light bulb in the garland, or there are obvious damages, you cannot use such an ornament.

The most important fire safety rule is not to leave lights on at night or when no one is home. And be sure to watch the children, because they are drawn to everything that flashes beautifully.

When decorating the Christmas tree, remember that the fasteners of the toys must be strong. You can not hang heavy toys on flexible and thin branches, it is better to cling them closer to the base.

The fire safety rules associated with the Christmas tree seem very strict only at first glance. By following these simple tips, you will protect your home from any possible troubles and give your loved ones a happy and fun holiday!

How to dispose of the Christmas tree left over from the New Year celebration? | Nature | Society

Maria Osina

Estimated reading time: 4 minutes

5764

Category: Plants

After the New Year holidays, the question arises: what to do with the Christmas tree? Most people, without hesitation, take out living spruce trees that are starting to crumble in the trash. This is not a very environmentally friendly solution, since wood, like other organic waste, decomposes in a landfill, emits carbon dioxide. Artificial Christmas trees are much more environmentally friendly in this regard, but they are not recyclable. Aif.ru learned from Head of the environmental movement "Separate Collection" Tatyana Nagorskaya , how and where you can dispose of the trees left from the holiday and how to do it with minimal harm to the environment.

How to dispose of an old artificial Christmas tree?

Do not dispose of an old artificial Christmas tree. As Tatyana Nagorskaya explains, the needles of artificial Christmas trees are usually made of polyester, and in this form it is not accepted for recycling. The only option not to throw an old artificial Christmas tree in the trash is reuse, that is, reuse. For example, from its branches you can make decorative compositions to decorate a house or garden plot. You can also give away an old artificial Christmas tree or sell it.

The Russian branch of Greenpeace notes that artificial Christmas trees are made of metal and plastic, and often use PVC (polyvinyl chloride, a type of plastic that includes phthalates - toxic substances). The organization says that an artificial Christmas tree only pays for its ecological footprint if it is used for 20 years.

Where can I donate live spruce?

Living spruce absorbs carbon dioxide while it is growing, thus helping to curb the rate of global warming. But at the same time, if a tree is simply thrown into a landfill after the holidays, then it, like any organic waste, will emit methane - and it is already affecting climate change. So, for example, a two-meter Christmas tree, decomposing in a landfill, emits about 16 kg of CO2 (carbon dioxide) into the atmosphere. The carbon footprint of living spruce can be reduced by burning the tree or processing it into wood chips. According to the estimates of the British company Carbon Trust, which helps business owners to make it more environmentally friendly, in this case, the carbon footprint can be reduced to 3.5 kg of CO2.

In Moscow, live spruces have been accepted for recycling for several years as part of the Christmas Tree Cycle campaign. As reported on the website of the Moscow City Hall, this year 380 points for the disposal of fir trees will open in the capital. In them, the trees will be processed into chips, which will then be used for composting and the production of soil or as bedding for animals. Similar points after the New Year holidays operate in the Moscow region.

In St. Petersburg, the action “Christmas trees, sticks and wood chips” was held earlier, organized by the environmental movement “Garbage. More. No, but this year it will not be held. From 2015 to 2018, activists collected 7.4 thousand trees. The processed wood chips were sent to centers for helping wild and homeless animals, as well as to the equestrian academy and bison.

Christmas tree collection points have been opened in many large Russian cities in recent years. For example, in 2019, Christmas trees were accepted for processing in Kazan, Ufa, Sochi, Yekaterinburg, Simferopol, Chelyabinsk, Yaroslavl, Barnaul and a number of other cities. They usually open on January 10-20. Information about the venues of the action, as well as the location of containers, can usually be found on the official websites of local administrations.

A Christmas tree can also be useful in the local zoo: elephants, polar bears, markhors and some other animals eat spruce or pine branches, bark and needles for food. Often, after the New Year holidays, zoos also announce tree collection campaigns.

See also:

  • "System kill in progress." Expert on the state of the country's forestry →
  • Where can I take Christmas trees for recycling in Moscow? →
  • Africa in miniature. How is hunting in Cameroon →

Christmas TreeHelpful TipsNew YearChristmas Tree Recycling

Next article

You may also be interested in